The 10 Most Scariest Things About Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A Fiat 500 key fob makes it easy to open doors and start your vehicle. However, there are numerous reasons why the fob won't be functioning. This includes a dead battery or water damage, problems with the receiver modules, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for your vehicle). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob doesn't work is the battery is dead. Modern key fobs only have a limited range of operation and must be within a few inches of your vehicle to work. If you are not within your car and press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".
If this happens, replace the coin-cell battery (Part Number CR2032) by a brand new one of a reputable brand such as Panasonic Duracell or Energizer. They are usually available at your local hardware store or online.
After you've replaced the coin cell battery you can test it by standing close to your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switch.
If your key fob still isn't working after replacing the battery, it could be water damage that hinders it from connecting to the module in your vehicle. Water damage can occur through a variety of methods, including the simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob was exposed to water, try placing it in a dry rice bag to draw the moisture back out. If this doesn't work your fob is likely to need to be reset by an experienced auto locksmith or by the dealer.
Water Damage
Damage to the water supply can occur if you submerge the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to short, and eventually cease to function. It's not a good idea to submerge the fob in water, but don't give it up even if you accidentally drop the fob in water or forget to remove it from your pants pocket.
First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl or a similar product. Test fiat 500 key replacement cost The Key Lab to see if it is functioning. If the key isn't working, it may have to be programmed again. This is usually done by a professional or dealer auto locksmith.
If the key is a newer model and was not programmed to your car It is likely that it needs to be replaced completely. A professional locksmith for automotive will be able to complete this process. The locksmith must cut the key to match the ignition on your vehicle. The locksmith also needs to reprogram your fob in the car's system. This is a cheap and quick process that can be completed within the same day.
Receiver Module Issues
Your 500 key fob may stop working because it is out of range. The remote has a range of 30 feet. So should you be too far from your vehicle it will not respond to your commands. You can fix this by moving the remote closer to your vehicle until it responds.
If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board problem. Reprogramming your fob can resolve this issue. There are instructions on how to do this for all automobiles by searching YouTube or reading the owner's manual.
It's possible that you need to replace the metal clips that keep the battery of your coin in place. If they loose tension, it could prevent your coin battery from sitting properly and cause your remote to malfunction.
In rare instances, the fob may become disconnected from your vehicle due to software issues or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances it is possible that the software will need to be reinstalled in your body control modules.
Interference
Interference can also cause the key fob to not be able to receive or transmit an signal. This can occur when the keyfob is located in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not work because of a weak connection to the buttons or water damage, or damage to the internal chips.
If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing the battery, reprogramming it and using the spare key fob, you may have a faulty receiver module on your 500. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then interpreted by the vehicle.
There's a quick and easy way to reset the 500's on-board system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then reconnect the battery. This will get rid of any remaining electricity and then restart the car's computer system, which could allow you to the key fob to function again. If the problem persists you should consult an expert technician. They can identify the exact cause of any problems.